forum.excito.org

Hail,
I can see the possible need to use the 2.4 GHz band as the WAN connection and using the 5 GHz band for a wireless access point. Does someone on this list know if both radios can be used simultaneously? If not, I will require a wireless access box to be connected to the B3 LAN port in addition ...

Ingo,
Thanks a lot. I may have to wait until I get back after Easter but I will indeed look into this. I suppose this thread should be carried over to B2 and B3 support.

aardic

Ingo,
HIDDEV is set now, which means that it can handle APC UPS'.
Have you been successful in getting this up and running on 2.4.1?
My installation does not create the udev rule required to provide hiddev.
I'm not sure that I have much time to address tis at present but would like to get apcupsd ...

Hail,
Ignore my previous post regarding B2 not loading RC3; my fault.

Hail,
I installed RC1 on two B2's following the steps outlined on the wiki and the procedure worked as advertised, however, upon applying the same procedure to RC3, one B2 came up (it works quite well now) but the other (the older one) will not pass the 2 Hz blinking light stage. I tried about 1 ...

This will only happen when you try to set up a password with a wrong syntax (e.g. starting with a '#').
@Johannes: please comment if neccessary.

Thanks

Oliver

I thought there were other restrictions. Anyway, the password I tried to set was 16 characters, 11-lower case, 1-upper case, 1-numeric ...

This will only happen when you try to set up a password with a wrong syntax (e.g. starting with a '#').
@Johannes: please comment if neccessary.

Thanks

Oliver

I thought there were other restrictions. Anyway, the password I tried to set was 16 characters, 11-lower case, 1-upper case, 1-numeric ...

I was able to change the admin password during upgrade but now cannot change it again as admin within the web interface; I'm stuck with the first password I set.
Has anyone else had this problem and if so, is there another way to change the web admin password?

What do you mean exactly? Is the ...

I was able to change the admin password during upgrade but now cannot change it again as admin within the web interface; I'm stuck with the first password I set.
Has anyone else had this problem and if so, is there another way to change the web admin password?

Hail,
My last show stopper was due to a typo in ups.conf.
Now the driver won't load and I receive the following message:
Network UPS Tools - Generic HID driver 0.34 (2.4.3)
USB communication driver 0.31
Can't claim USB device [051d:0002]: could not detach kernel driver from interface 0: Operation ...

Hail,
I am not sure whether I should be adding to this thread or starting a new one.
I installed NUT on bubba3 (obtained from the bubba3 repositories) and
upon running upsdrvctl :
/etc/nut# upsdrvctl start
Network UPS Tools - UPS driver controller 2.4.3
Can't start /lib/nut/usb-hid-ups: No such ...

Hail,
How do I set the hardware clock (preferably from the command line)
of Bubba2? The hwclock command results in:
----------------
>:~$ sudo hwclock -r
Password:
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method ...

Hail,
Has your issue been resolved? I experienced the same problem although enough
of the installation proceeded that I was able to use specific features I require.
I would like to clean things up eventually.
I do not use Horde and I disabled mysql after upgrade as I do not require it.
I prefer ...

Tor,
Your suggestion was exactly what I needed. Thank You.

Rick

Hail,
What is the cleanest way of disabling mysql in Bubba|two?
It uses a lot of memory and I am currently not using it.

Rick